Fn050-Vdk.4i.V7p1 Ziehl Abegg Fan

Artikelnummer: 167240

Axial fan with sickled blades and square wall ring plate. Type: FN063-4DQ.6N.V7P6 3 ~ 230 / 400V ± 10% D / Y 50Hz P1 1.75kW 6.4 / 3.7A DI = 5% 1400 / MIN COZY 0.68 70 ° C 3 ~ 230 / 400V ± 10% D / Y 60Hz P1 2.80kW 8.4 / 4.8A DI = 5% 1580 / MIN COZY 0.84 60 ° C 3 ~ 265 / 460V ± 10% D / Y 60Hz P1 2.90kW 8.0 / 4.6A DI = 10% 1640 / MIN COZY 0.80 60 ° C IP54 THCL 155 ErP compliant 2015 N = 42.5 statA = 37.5% Terminal box K62 firmly built on stator. Circuit diagram: 1360-106XA Rating plate: 1x fixed. Installation position H / Vu / Vo. Motor protection: thermostat switch Operating mode: continuous operation with occasional Startups (S1) according to DIN EN 60034-1: 2011-02 Occasional start-up between -40 ° C and -25 ° C is permitted. Permanent operation below -25 ° C only with special Storage for refrigeration applications possible on request. Moisture and tropical protection. Ball bearings with long-term lubrication .. Aluminum wing. Stator paint: unpainted Painting rotor: unpainted Painting wing: unpainted Engine suspension, powder-coated, resistance class 2 (504 h NSS, KK) RAL 9005 (deep black). Wall ring, powder-coated, resistance class 2 (504 h NSS, KK) RAL 9005

Et2r-1024/38/30v

Encoder shaft: 38.0 mm Resolution: 1024 pulses Voltage: 10-30 VDC Cable length: 10.00 m

DX fan FN045-4EK.2F.V7P2

motor

Fan [RF22P-2DK.3F.5R

OR[RF22P-2DK.3F.5R/MVI],2320Nm3/min,470PA/620PA,0.49kW,400V,STEEL,2320rpm,FOR SIEMENS MOTOR Q4371019

Ziehl-Abegg Zadyn4cs/ 62 A

205165

Crossflow fan with capillary chord and Single-phase AC motor. Type: QK08B-2EM.50.CH 1 ~ 230V ± 10% 50Hz P1 0,27kW 1,2A 2470 / MIN 6UF / 400V 1 ~ 230V ± 10% 60Hz P1 0,28kW 1.2A 2600 / MIN 6UF / 400V PsF min.50PA Operating capacitor firmly established IP10 thermal class 130 ErP compliant 2015 N = 23.7 TOTB = 19.1% Connection via European terminal block, operating capacitor built and connected Rating plate: 1x fixed Installation position H Engine storage with standard lubrication Counter bearing with cold grease Without 180 degree guide plate (standard) Impeller made of aluminum Motor mounting side B (anti-clockwise)

Type: Rh22m-2dk.1b.1r

Artikelnummer: 121860E Single-flow motor fan with backward curved blades 3 ~ 400V ± 10% Y 50Hz P1 0.19kW 0.34A 2700 / MIN COZY 0.81 70 ° C 3 ~ 400V ± 10% Y 60Hz P1 0.31kW 0.47A DI = 5% 2840 / MIN COZY 0.94 40 ° C 3 ~ 460V ± 10% Y 60Hz P1 0.34kW 0.46A DI = 5% 3010 / MIN COZY 0.94 40 ° C IP44 THCL 155 ErP compliant no Connection cable laterally, 105cm. Schematic: 1360-159XA sandwich label Rating plate: 1x fixed. Installation position H / Vu / Vo. Motor protection: thermostat switch Operating mode: continuous operation with occasional Start-ups (S1) according to DIN EN 60034-1: 2011-02 Occasional starting between -40 ° C and -25 ° C is permissible. Permanent operation below -25 ° C only with special Storage for refrigeration applications available on request. Wet / tropical protection. Balancing weight G 6.3

Imb3

siehe Bild

L-Erp_Pauschale (Flat Rate)

113045e

Single-flow motor fan with backward curved blades Type: RH28L-2EP.WD.1R 1 ~ 230V 50Hz P1 290W 1.24A DI = 0% 2250 / MIN 8uF / 400V 45 ° C THCL 155 IP44 depending on installation and position according to EN 60034-5 ErP compliant no Capacitor not included Connection cable variable 45cm. Schematic: 1360-177X sandwich label Rating plate: 1x fixed. Installation position H / Vu / Vo. Motor protection: thermostat switch Balancing weight G 6.3 Condensate holes in the stator and rotor open Stator unpainted Rotor with 1-coat finish RAL 5002 (ultramarine blue).